In the following page’s, the components shown are used to build a Cup-lock scaffolding. Most of the components used are common to all three systems of scaffolding. All products have been manufactured in accordance with previous mentioned regulations, have been tested in accordance with European standards, produced using S 235 JR steel, and have been have been processed by hot-dip galvanization.
Leveling Jack with Base Plate
Leveling jacks are used to set vertical posts at the same height. Their base plate has a thickness of 5 mm and its dimensions are 150 mm x 150 mm square shaped, bars are made with a tube of Ø38*4 mm. The tube, as long as 500mm, can be adjusted to 350mm and the tubes of 750mm can be adjusted to 560mm. Total length of the elements can vary. These measures are: 0.50 m, 0.75 m, 1.00 m, 1.20 m.
Vertical posts are the main elements of the rosette modular scaffolding system. They are produced from steel tubes with section of Ø48,3x3mm. Every vertical post has a rosette at each 50cm. Rosettes are produced from 8mm steel plates and welded in horizontal position. The tube that is used to join each bar with the upper bar is made by steel tube with section of Ø40x2.5mm.
Horizontal bearers are used as joining elements between vertical posts. They are produced from steel tubes with sections of Ø48,3x2.5mm. Bar length can be 0.70 m, 1.10 m, 1.50 m, 2.00 m, 2.44 m and 3.00 m. This type of bar can be produced with different types of wedged heads to work as a joint with rosettes. Wedged heads can be made with curved steel plates welded in two sizes or also made by steel casting.
Shoring braces are opposed to the forces coming horizontally in the scaffolding system. They also play a role to help to set up the scaffolding. They are made from steel tubes of Ø48,3 x 2,5mm section. The bars are made in the following sizes: 3.75 m, 3.25 m, 2.75 m, and 2.25 m. 3.25 m bar is the most common used size. NOTE : Every size mentioned above is referred to the total length of the bar.
Access Deck with Ladder
Access decks with ladders are used by workers to access other levels of the scaffolding system, and to also discharge materials. They are produced from rectangular steel profiles of 40x60x2mm. The trapdoor direction can be changed upon request. Their sizes are variable. The standard width is 60 cm, whilst their length can be 2.00 m, 2.50m, 3.00m, 2.50m (being the most commonly produced and used).
Step stairs can be used by workers to access to another level within the scaffolding itself and to also discharge materials. In the rosette modular scaffolding system, it has to be used next to a steel deck in order to access other levels. Minimum use for the stairs must be equal to three steel decks. It is able to cover dimensions between 3.00 m, 2.50 m with a maximum height of 2 meters.
Steel decks are used to assure the workers to walk inside the scaffolding. They’re manufactured by profiled steel sheet of 320 mm width and mainly thickness of 1,5 mm with a special self-made design, and is anti-slip. They can be manufactured in the following lengths 0.70m, 1.10m, 1.50m, 2.00m, 2.50m and 3.00m, 2.50 m (being the most common size). All these types of decks can also be manufactured in different thicknesses as 1.5 mm, 1.35 mm, 1.25 mm by special request.
Board brackets are used to create an additional working place in the spaces under cornices of buildings. They are manufactured from steel tubes with a section of Ø48 mm diameter and a thickness of 3mm. Their width can be 0.70m, 1.10m, 1.50m in order to set different types of space needed, and can be manufactured upon customers’ request.
Is a panel located at foot height that is used to avoid materials and tools to fall off from decks. They are manufactured from steel plates with 1,50 mm thickness. They can be manufactured as the same lengths as steel decks that 0.70m, 1.10m, 1.50m, 2.00m, 2.50m and 3.00 m, 2.50 m (being the most common size).
Wall Mount Bracket
This element is used to anchor the scaffolding system to the walls of buildings. They are manufactured from steel tubes with section of Ø48,3 x 3,2 mm with a clamp at its end. To be able to make the connection possible, their bolts have to be screwed into the wall. The distance between the scaffolding and the wall can be adjusted by the clamp and the tube, that has a length of 50 cm.
Wall Mount Pipe Clamp
Used to anchor the scaffolding system to the walls of buildings. They are manufactured from steel threaded rods with a diameter of 12mm and at their end is a bolt that helps to increase the anchorage of the scaffolding to the wall. It allows a range of adjustment to 1.00 m from 0.50 m thanks to its threaded rod. The most common distance of use is 50 cm.
Head Spindle “U”
Are upper adjustment bars used to set the surfaces above them for the same height. They are used normally to support the formworks used to make slabs. The U is manufactured with a plate of thickness 5 mm and width of 100 mm, its base is 125 mm and wings 40 mm. The bar is made with tube of Ø38*4 mm. The length of the whole piece are standards of 0.50 m, 0.75 m, 1.00 m.
Head Spindle “T”
Are upper adjustment bars used to set the surfaces above them for the same height. They are used normally to support the formworks used to make slabs. The upper T is manufactured by 5 mm steel plate and its width 250 mm, where it’s base is 125 mm and wings are 40 mm. The bar is made with tube of Ø38*4 mm. The length of the whole piece are standards of 0.50 m, 0.75 m, 1.00 m.
Four-Way Head Spindle
Are upper adjustment bars used to set the surfaces above them at the same height. They are used normally to support the formworks used to make slabs. The base plate is manufactured with a plate 5 mm thick, 260 mm width and 175 mm length. L shaped profiles that are welded at the corners are 190 mm height, and the L is formed by wings 40 mm long and 4 mm thickness. The bar is made with tube of Ø38*4 mm. The length of the whole piece are standards of 0.50 m, 0.75 m, 1.00 m.